How to apply coating Body – Autobody Ceramic Nano Coating

 

Pearlnanobase-1

How to apply Body coating – Green Bottle
Notes before applying:
Please Note: This is a professional product, made for professionals. Only apply Pearl Nano Coatings to vehicles that have been perfectly polished and is free of any and all scratches, marring or imperfections. Please follow the directions listed here + suggested wipe-down wait times.
– Do not apply under the scorching sun, in the rain, or sub-zero temps.
– Apply only after the auto body has cooled completely.
– Apply by hand.
– Remove any dirt attached to the car body.
– Make sure the car body is dry.
1. Clean Car, Remove surface contaminants and iron particles in the paint using a clay bar.
2. Remove all Scratches and Polish to perfection.
3. Remove any oils left behind from polishing compounds
Only Now are you ready to apply the coatings
1. Pay attention, use great lighting and use the guidelines set here.
2. Place 5-10 drops of Pearl AutoBody coating on the sponge (this should cover about half a car door).
3. Apply to the car body 1 square part by 1 square part at a time. Apply the coating evenly is very important. Everyone has a different method. We recommend going in a small circle, then in a starburst pattern and then lengthwise direction and then breadthwise. Do this 1-2 times or until you see that the portion you are covering has an even amount of coating applied to it.
4. After applying, wait for alotted time: When the room temperature is:
a. 10 degrees C (50F),: wait 4 minutes,
b. 20 degrees C, (68F) wait 2-3minutes,
c. 20+ degrees C, (70F+) wait 1-2 minutes
Hotter than 25C or 85F wait 20-30 seconds.
Once the timeframe has past, use a DRY microfiber towel to polish it into a high gloss. The best time to wipe the surface is when you feel a little resistance. If the temperature is very hot, (90F+) you may want to use an initial damp microfiber towel to remove and then a dry one.
5. Do not wait too long time after application to wipe and dry as indication in Step 4, otherwise, when the Pearl AutoBody coating is hardened fully, it is very hard to remove.
If you wait too long and it dries super hard…do not panic. Polish it down using a course cutting polish and a machine polisher.
Please Note: This is a professional product, made for professionals. Only apply Pearl Nano Coatings to vehicles that have been perfectly polished and free of all scratches, marring or imperfections. Please follow the directions listed here and suggested wipe down wait times.
Key points:
1. USE Lots of Lights. The room light should be strong enough, to make sure each part is wiped by towel timely.
2. For big parts like the engine hood, you should divide the area into several small squares to apply the coating. Look into the glare to see if you missed any areas.
3. Do not add water any more water to the foam sponge once you start coating the body.
4. Wipe the coating immediately if it adheres to the glass. It not meant to be used on the glass.
5. You should not use the same application sponge or surface of towel to wipe the entire time; you need to change applicators and the wipe down towel often.

The Pearl AutoBody Pro Coat can be applied 30 minutes after the Base coat is applied, unless the temperature is below 50F with high humidity. Then wait 1-2 hours to apply the Pro Coat.
How to apply Pearl Nano Pro Auto Body coating: Blue Bottle
Notes before applying:
Please use the Same guidelines as the base coat.
1. Pay attention, use great lighting and use the guidelines set here.
2. Place 5-6 drops of Pearl Nano Pro AutoBody coating on the sponge (this should cover about a 2’x2’ area or 3’x3’ area).
3. We recommend going in a small circle, a starburst pattern and then in a lengthwise direction and then breadthwise. Do this 1-2 times or until you see that the portion you are covering has an even amount of coating applied to it.
4. IMPORTANT – After applying, wait for about 1-2 minutes. (if 60F to 80F) Because the surface is much slicker than the base coat was on the paint. This is thinner and dries faster. Please be sure you understand this. This is where new installers make mistakes.
Once the timeframe has past, use a DRY microfiber towel to polish it into a high gloss. Use a 2nd clean towel to buff again.
DO NOT PUSH VERY HARD. Move to next section.
5. Do not wait too long time after application to wipe and dry as indication in Step 4, otherwise, when the Pearl AutoBody coating is hardened fully, it is very hard to remove.
Key points:
You should not use the same application sponge or surface of towel to wipe many cars; You need to change applicators and the wipe down towel often. If it begins to dry and harden, it can scratch the surface.

Maintain the car afterwards with care. Pearl Professional Waterless Car Wash is a perfect product to use. Even washing with high quality soap and water is ok. Do not let the soap dry nor the hard water.
The better you treat the car and the exterior, the longer the coating will last.

Remove bird droppings and other contaminants quickly

Tel: 866 285-1051 Toll free
E-mail: Dave [@] PearlUSA.net

http://www.pearlnano.com/

Ask about a Sample Pack and Price List Click Here to Get a Price List and More Info

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s